If you’re wondering how to reink a Maxlight Stamp, you’ve come to the right place. This post explains how to reink your Maxlight Stamp, so you can keep using it for thousands of stamping applications. Follow these simple steps and you’ll be able to use your Maxlight Stamp thousands of times before you have to replace the ink. Read on to learn more! Also, you can learn about the PSI and XStamper pressure to reink your stamp.
Re-inking
Using re-inking fluid for your MaxLight Stamp is easy. You simply fill the stamp with eight to ten drops of MaxLight Ink. Unlike traditional stamp ink, which must be removed after use, MaxLight Ink is easy to apply and remove. The ink can then sit for 45 minutes to dry before being used again. However, if you accidentally ink your stamp, you can always use a new batch of MaxLight Ink.
If you do not have enough ink to make more impressions, you can purchase refill ink from the MaxLight website. This ink comes in different colors to match different stamps and can be purchased in various quantities. You can also purchase MaxLight refill ink for pre-inked stamps made by Ultimark and Accustamp. If you’re planning to re-ink a pre-inked stamp, check the Maxlight sizing chart to see which size you need.
XStamper
If you’ve got an XStamper, you can reink it as many times as you want, and the Maxlight Stamp is a great option for this. Unlike many other stamps, the Maxlight can be used thousands of times before it needs to be reinked. To use it, you just need two to six drops of ink. And, you can get 50,000 impressions out of it without re-inking.
The Maxlight ink can be used with oblong ports. You can’t use other brands of ink with this stamp, and other inks can damage it. You can add ink to one port, two ports, or all of them. Make sure you put the right amount in each port to get the best results. Then, you’ll be ready to use your new stamp!
When refilling your XStamper Maxlight Stamp, you need to use the correct ink. The ink for the Maxlight Stamp is formulated specifically for it, so you won’t be able to use another brand’s ink. After filling the Maxlight Ink, you should wait at least 45 minutes before using it. However, you can remove the ink cartridge from the stamp and place it back into the ink tray.
Trodat
To reink your MaxLight stamp, you should first use oil-based ink for rubber stamps. You can use either a water-based or oil-based ink for your MaxLight stamp. Water-based ink works better with rubber stamp pads. Water-based ink is more flexible. If you need to stamp multiple colors, use different inks. When you’re ready to use an oil-based ink, you can add about 5 drops per hole.
To reuse the ink in your MaxLight stamp, simply place it on a flat surface. Apply the ink to the ink pad in even drops, and wait a few moments for it to absorb. Then, replace the ink pad. Follow the steps outlined in the video below to apply the ink. Once the ink has dried, remove the old ink pad. Repeat the process.
Re-inking the MaxLight stamp is easy, too. To replace the ink, you need to use an ink compatible with the existing stamp ink color. Then, apply six to eight drops of the new ink into the inking well. Leave it to dry for 1 hour. Repeat this process as necessary until the impressions are darkened. Using the right ink is essential to getting the most out of your stamp.
PSI
If your stamp has run out of ink, you may be wondering how to reink your stamp. Fortunately, you can use replacement inks to extend the life of your MaxLight stamp. These inks are also compatible with other brands of pre-inked stamps from Trodat. Each brand has a slightly different chemical composition, and you should avoid changing the inks in each type unless you’re using the same stamps from both manufacturers. Reinking a MaxLight stamp is as simple as ordering replacement ink. Simply select the color of ink you need, increase the quantity and click on the “add to cart” button.
Before you go out and purchase a new PSI stamp, consider how much it would cost you in the long run. A self-inking stamp is much cheaper than a traditional self-inking stamp. You can get thousands of impressions before having to reink it again. You will also benefit from a lifetime warranty. These are two of the reasons to choose a self-inking stamp. You’ll be happy you did.
XStamper re-inking fluid
Re-inking your stamp is a breeze with MaxLight re-inking fluid. There are many ink colors to choose from, and each re-inking fluid comes with a corresponding brush. Simply follow the directions on the XStamper’s label to change the ink. Using this re-inking fluid is simple, and it will make your stamp’s re-impressions crisp and clear.
To re-ink your Maxlight stamp, insert the re-inking pad into the center opening. Place a couple of drops of ink into the re-ink pad, and then push the stamp in. Ensure that the ink saturates the pad completely before re-inking. When done, push the buttons on the side to lock the stamp in place.
XStamper re-ink fluid for maxlight stamp contains oil-based ink designed for MaxLight pre-inked stamps. It is best to use oil-based ink with MaxLight re-inking fluid, since the water-based ink is compatible with other brands of self-inking stamps. Use the ink in a pre-inked MaxLight stamp to prevent the stamp from drying out and becoming discolored.
MaxLight ink
The MaxLight stamps are re-inkable, extending the life of your pre-inked stamps. You can reink your MaxLight stamps with re-inking fluid, available in a variety of colors. You can also use the re-inking fluid to re-ink Accustamp and Ultimark pre-inked stamps. Here are some tips for re-inking your MaxLight stamp.
Before using your MaxLight stamp, you should be sure to purchase a new bottle of ink. You should also purchase a new stamp if your previous one dried out. You can buy new ink at a local craft store or online. When ordering your MaxLight ink, make sure to purchase the color that matches your stamp’s design. You can also check the instructions on the ink bottle.
To reink a MaxLight stamp, add new Maxlight re-fill ink to the die box’s slotted back. Then, push the handle back on the mount. Let it sit overnight to ensure the ink migrates through the stamp. Then, test your stamp and see if it’s ready for use. If it doesn’t, try reinking it again. Once it’s completely ready, you can use it to create fresh, beautiful designs on your cards.
About The Author
Mindy Vu is a part time shoe model and professional mum. She loves to cook and has been proclaimed the best cook in the world by her friends and family. She adores her pet dog Twinkie, and is happily married to her books.